FOAMIRAN FLOWER HEADBAND

Send

On the rim, small flowers are located on one half, made of plastic suede without special tools.

To work on the decoration we take the materials:
- the rim.
- acrylic paints.
- scissors.
- wire.
- plastic suede pink and green.
- thin satin ribbon.
- sponge or foam rubber.
- a pencil with a fixed eraser.
- hair curlers.
- a plastic sheet for printing invoices.
- stamens for flowers.
- a toothpick.
- lighter.
- thin green paper.
- Moment glue is transparent.
The composition will have 11 flowers, each with 2 rows of petals. Therefore, from pink suede you need to cut 22 squares with a side of 4 cm. And from the green color of the material you will need 8 rectangles 5 x 3 cm.

Now on these bases we will make petal circles and leaves.

From the green details we make the shape of the sheet. And from the pink parts, first cut out a circle, rounding the corners. Then, arbitrarily, from the center, divide it into 5 petals, and cut it out only according to the upper roundings. Next, we trim the edge of each petal towards the center, leaving the middle with a diameter of 1.5 cm whole.

Now we pass to coloring. We take yellow and red acrylic paint and apply a piece of foam on the edges of the petal circles on both sides.

A yellow center should be applied only on one side.

Leave the petals to dry completely and go to the leaves. First you need to make streaks on them. The first way you can simply draw with a toothpick on the sheet itself. And in the second method, you can use a plastic sheet with a convex structure. But for this, the leaf itself should be warmed up a little, applying to the hair curler.

And immediately apply a warm template to the texture, pressing it well.

On the leaves should get a clear imprint of the veins.

Now, these blanks should be painted a little red only on the edge on both sides.

But the processing is not completed. Next, you need to trim the shape of the sheet with scissors so that the main vein is in the middle of the workpiece. Then along the edge we make small denticles. Now we fold the sheet in half and with a fold touch the warm curling iron for a few seconds, and then press it with our fingers, it turns out an interesting fold.

While laying the leaves aside. Back to the flowers. In addition, you need a pencil with an eraser and a sponge. It is necessary to give the petals a new shape. We heat the circle on the curling iron, place it on the sponge and press the middle of the petal circle deep into the foam with an eraser.

We get a cup-shaped blank. It must be taken into account that the yellow part must remain inside.

With these movements we process all the petals.

But the beauty of the circles is a different treatment. Now you should separately process each petal of the flower circle with a lighter. On a small part, we make two folds. We warm with a lighter and, while the suede is warm, with our fingers we form a bend. This will need to be done from two sides.

We process all 5 parts of the petal circle.

This form allows the flower to be magnificent.

Now go to the stamens. For one flower, we use a pair of double blanks. Cut 11 pieces of wire 5 cm long. On one edge of the segment we apply stamens folded in half, 1 cm above the wire. And we fix it a bit by winding the thread.

When the stamens are ready, you should immediately glue the entire wire with strips of thin green paper.

We pass to the dried leaves. For them, too, should prepare pieces of wire 6 cm long. Then we attach the sheet to the wire, piercing the lower part of the sheet several times.

Then you need to glue the sheet and wire along the front side and glue it well on the bend. Now take the petal circles and fold them in pairs, two together, glue a little in the center. Then we pierce in the middle with a toothpick, making a hole.

And then we insert stamens there and again we glue the joints.

On finished flowers, you need to make bends of the wire. We retreat 1.5 cm from the workpiece and on green stems we make a bend at 90 degrees. And go to the assembly on the rim.

We start the winding with a thin tape from one edge of the rim, lubricating with glue at small intervals. After passing a tape 10 cm from the edge, we apply a sheet, tilting a corner to the bottom of the rim, and make a few turns with a ribbon along the stem.